FWS‡>P´@Cÿÿÿ?f>ˆÒÊ_rootSet arp type (arpa, probe, snap) or timeoutarpsubintGCaddSCEnable ARP for a frame relay interfaceframe-relaySet ARP cache timeouttimeoutSeconds<0-2147483>Set bandwidth informational parameterbandwidthBandwidth in kilobits<1-10000000>Transparent bridging interface parametersbridge-groupAssign an interface to a Bridge Group.<1-255>Filter packets by source addressinput-address-listEthernet address access list<700-799>Deny input LAT service advertisements matching a group listinput-lat-service-denyA list of LAT service advertisementsAll LAT groupsallRemove from existing group code listdisabledAdd to existing group code listenabledPermit input LAT service advertisements matching a group listinput-lat-service-permitFilter incoming IEEE 802.3 encapsulated packetsinput-lsap-listEthernet type access list<200-299>Filter input with a pattern listinput-pattern-listPattern access list number<1100-1199>Filter incoming Ethernet packets by type codeinput-type-listEnable LAT compression over serial or ATM interfaceslat-compressionFilter packets by destination addressoutput-address-listDeny output LAT service advertisements matching a group listoutput-lat-service-denyPermit output LAT service advertisements matching a group listoutput-lat-service-permitFilter outgoing IEEE 802.3 encapsulated packetsoutput-lsap-listFilter output with a pattern listoutput-pattern-listFilter outgoing Ethernet packets by type codeoutput-type-listSet interface path costpath-costPath cost (higher values are higher costs)<0-65535>Set interface prioritypriority<0-255>Disable spanning tree on a bridge groupspanning-disabledConfigure subscriber loop controlsubscriber-loop-controlSpecify delay for interface transitionscarrier-delayCarrier Transitions delay seconds<0-60>CDP interface subcommandscdpEnable CDP on interfaceenableSet a command to its defaultsdefaultSpecify interface throughput delaydelayThroughput delay (tens of microseconds)<1-16777215>Interface specific descriptiondescriptionUp to 240 characters describing this interfaceLINEExit from interface configuration modeexitInterface Internet Protocol config commandsipSet the IP address of an interfaceaddressIP addressA.B.C.DIP subnet maskMake this IP address a secondary addresssecondaryVPN Routing/Forwarding parameters on the interfacevrfConfigure forwarding tableforwardingTable nameWORDConfigure route-map for routes received from this sitesitemapName of the route-mapSet the interface Maximum Transmission Unit (MTU)mtuMTU size in bytes<1500-2025>Negate a command or set its defaultsnoShutdown the selected interfaceshutdownConfigure NTPntpConfigure NTP broadcast servicebroadcastListen to NTP broadcastsclientConfigure broadcast destination addressdestinationDestination broadcast IP addressHostname or A.B.C.DConfigure broadcast authentication keykeyBroadcast key number<0-4294967295>Configure NTP versionversionNTP version number<1-3>Disable NTPdisableConfigure NTP multicast servicemulticastMulticast group IP addressListen to NTP multicastsMulticast client IP addressConfigure multicast authentication keyMulticast key numberTTL of the multicast packetttlTTLConfigure priority schedulingpriority-queueegress priority queueoutConfigure QoS Service Policyservice-policyKeep history of QoS metricshistoryAssign policy-map to the input of an interfaceinputpolicy-map nameAssign policy-map to the output of an interfaceoutputDefine timeout values for this interfaceDefine session timeout value for this interfaceabsoluteSession lifetime (in minutes)<0-35790>Session lifetime (in seconds)<0-59>Configure weighted round-robin xmt queueswrr-queueConfigure WRR bandwidthenter bandwidth weight for qid 1<0-65536>enter bandwidth weight for qid 2enter bandwidth weight for qid 3Configure cos-map for a queue idcos-mapenter cos-map queue id<1-4>8 cos values separated by spaces<0-7>Configure dscp-map for a queue thresholddscp-mapenter dscp-map threshhold id (1-2)<1-2>dscp values separated by spaces (up to 8 values total)<0-63>Configure queue-limitqueue-limitenter queue size weight for qid 1<1-100>enter queue size weight for qid 2enter queue size weight for qid 3Configure random-detectrandom-detectmax-thresholdsmax-thresholdenter threshold queue id (1-4)enter percent of queue size for threshold 1Configure queue tail-drop thresholdsthresholdenter percent of queue size for threshold 2enter–”„,––R––N–R––N–R– –N–N–R––R– –N–R––R––N–R––N–N–R––N–N–N–R––N–N–R––N–N–N–R––N–N–N–R––N–N–N–N–R– –N–N–N–N–R–!"–N–N–R––N–N–"N–R––N–N–"N–R––N–N–"N–N–R– –N–N–"N–N–R–#$–N–N–R–%&–N–N–$N–R–'(–N–N–R–)*–N–N–(N–R–+,–N–N–R–%&–N–N–,N–R–-.–N–N–R–/0–N–N–R––N–N–0N–R–12–N–N–R––N–N–2N–R––N–N–2N–R––N–N–2N–N–R– –N–N–2N–N–R–34–N–N–R––N–N–4N–R––N–N–4N–R––N–N–4N–N–R– –N–N–4N–N–R–56–N–N–R–%&–N–N–6N–R–78–N–N–R–)*–N–N–8N–R–9:–N–N–R–%&–N–N–:N–R–;<–N–N–R–=>–N–N–N–ÉO––N–N–@N–BN–ÉO––N–N–DN–ÉO––N–N–FN–ÉO––HN–JN–ÉO––LN–NN–ÉO––PN–N–N–ÉO––PN–N–N–ÉO––PN–N–ÉO––PN–N–N–ÉO––PN–N–N–N–ÉO––PN–N–N–N–ÉO––PN–N–N–"N–ÉO––PN–N–N–$N–ÉO––PN–N–N–(N–ÉO––PN–N–N–,N–ÉO––PN–N–N–.N–ÉO––PN–N–N–0N–ÉO––PN–N–N–2N–ÉO––PN–N–N–4N–ÉO––PN–N–N–6N–ÉO––PN–N–N–8N–ÉO––PN–N–N–:N–ÉO––PN–N–N–